Stopping now may result in an incomplete set of software on :. Click Resume to continue the installation or Stop if you are sure you want to stop.
An error occurred while reading or writing the file “^0” on “:.” No installation can take place. (Error #^1)
An error occurred while reading or writing the file “^0” on “:.” Installation cannot continue. The disk “:” may not be a usable startup disk. (Error #^1)
An error occurred while reading the file “^0” on “^1.” No installation can take place. Make sure you are using the original Installer disks. (Error #^2)
An error occurred while reading the file “^0” on “^1.” Installation cannot continue. The disk “:” may not be a usable startup disk. Make sure you are using the original Installer disks. (Error #^2)
There's a problem with the disk “:.” No installation can take place. (Error #^0)
There's a problem with the disk “:.” Installation cannot continue. The disk “:” may not be a usable startup disk. (Error #^0)
There's a problem with the source disk “^0.” No installation can take place. Make sure you are using the original Installer disks. (Error #^1)
There's a problem with the source disk “^0.” Installation cannot continue. The disk “:” may not be a usable startup disk. Make sure you are using the original Installer disks. (Error #^1)
The Installer document “^0” is damaged. Make sure you are using the original Installer disks and try again.
This is not the correct “^0” disk. Make sure you are using the original Installer disks and try again. Click Continue if you have the correct disk to insert. Click Stop to stop any further installation.
The file “^0” on disk “:” cannot be replaced by the Installer. No installation will take place. Quit the Installer, move the file to another folder and try again.
“^0” has the correct name but does not have the expected contents. Click Continue, then try inserting a different disk with this name. Or click Stop to stop any further installation.
No installation was necessary on “:.”
The Installer did not find any Installer documents and cannot run without one.
Installation was stopped before it was completed. The disk “:” may not be a usable startup disk.
Error copying desk accessory onto “:.” Installation cannot continue. The disk “:” may not be a usable startup disk.
The file “^0” already on “:” is newer than what you are about to install. Click Newer to keep the newer file, Older to replace that file, or Cancel to leave the disk “:” untouched.
The Installer found ^0 Installer documents on the disk “^1.” Please open the specific document you wish to use.
Some of the files on the disk “^0” do not meet requirements specified by the Installer document “^1.” Installation cannot continue. The disk “:” may not be a usable startup disk. Make sure you are using the original Installer disks.
Cannot overwrite a protected resource on the disk “:.” Error detected before installation began.
Error occurred while writing the boot blocks. “:” may not be a usable startup disk. (Error #^0)
System Software is required for this installation but is not present on “:.” Click OK, then install System Software before or as part of this installation.
A file is missing from “:” but is required for this installation. Quit the Installer and check your manual to see what files are required and how to get these files.
The file “^0” is missing on “:” but is required for this installation. Quit the Installer and check your manual to see how to get that file.
There were files missing on “:” that are required for this installation. Quit the Installer and check your manual to see what is required.
There are too many desk accessories on “:” to complete this installation. Installation would result in ^0 desk accessories; only ^1 are allowed. Please quit the Installer, remove some desk accessories, and try again.
There was nothing to remove from “:.”
“^0” is the wrong disk. To finish the installation, click Continue and insert “^1.” To stop any further installation, click Stop.
Installation was cancelled, leaving the disk “:” untouched.
The file “^0” already on “:” is more recent than what you are about to install. Click Continue to replace “^0” with the older version. Click Cancel to leave the disk “:” untouched.
The file “^0” on “:” does not meet the requirements specified by the Installer document “^1.” Installation cannot be completed. You may want to quit the Installer, remove “^0” and try again.
There is not enough space on the disk “:” to complete the installation (^0K needed, ^1K available). Quit the Installer, remove some items from the disk “:”, and try again. Or try installing on another disk.
There is something wrong with the selected disk “:” . An error occurred before installation began. You may want to try installing on a different disk or Quit to exit the Installer.
The Installer document “^0” is unusable for installation. The installation cannot be completed. The disk “:” may not be a usable startup disk. Make sure you are using the original Installer disks.
The Installer document “^0” is unusable for installation. An error was detected before installation began. Make sure you are using the original Installer disks.
^0 cannot run on this model of Macintosh. Please use Installer 2.6 disks to do this installation. Click Quit to leave the Installer.
Removal from “:” was successful. If you are finished, click Quit to leave the Installer. If you wish to do additional installations or removals, click Continue.
Installation on “:” was successful. If you are finished, click Quit to leave the Installer. If you wish to do additional installations, click Continue.
The selected disk is too full. Please quit the Installer and remove some files you no longer need.
There are too many files open on your Macintosh. Please quit the Installer, quit any other applications you may be running, and try again.
The disk is locked.
One of your disks is no longer available. Please quit the Installer, restart your Macintosh, and try running the Installer again.
A necessary file is locked. Installation cannot continue.
A problem occurred with the AppleTalk network. Please quit the Installer, restart your Macintosh, and try running the Installer again.
Out of memory. Please try running the Installer again. If this error occurs more than once, try running a different copy of the Installer.
An AppleShare server has unexpectedly shut down and installation cannot continue.
A disk error has occurred and installation cannot continue. Your disk may be damaged.
You do not have the necessary privileges to access all of the files needed on the server. Contact your AppleShare administrator.
A needed file is already in use or was left open.
There has been a problem with the file server. Perhaps you do not have the necessary privileges. Check with your network administrator.
